Wagner SprayTech 840i Uživatelský manuál

0802 © 2002 Titan Tool Inc. All rights reserved. Form No. 313-1797, REV APrinted in the U. S. A.Do not use this equipment before reading this manual

Servicing the Fluid SectionUse the following procedures to service the valves and repackthe fluid section. Perform the following steps beforeperformi

15. Insert the spacer on top of the upper packing.16. Thread the upper seal retainer into the upper housing andtorque to 25-30 ft. lbs.17. Insert the

Solution1. Plug the unit in.2. Reset the breaker.3. Turn the pressure control knob clockwise tosupply power to the unit and increase thepressure setti

©Titan Tool Inc. All rights reserved. 13TroubleshootingProblemExcessive surge at the spraygun.Poor spray pattern.The unit lacks power.Cause1. Wrong t

14 ©Titan Tool Inc. Tous droits réservés.Consignes de sécuritéCe manuel contient des informations qu'il faut lire etcomprendre avant d'util

©Titan Tool Inc. Tous droits réservés. 1514. L’action sur la gâchette produit une force de recul surla main tenant le pistolet.La force de recul du p

16 ©Titan Tool Inc. Todos los derechos reservados.Precauciones de SeguridadEste manual contiene información que tiene que leerse yentenderse antes de

©Titan Tool Inc. Todos los derechos reservados. 1713. Limpieza de la unidad.Nunca debe utilizarse una boquilla gruesa para pulverizarla unidad. En pa

18 © Titan Tool Inc. All rights reserved.Parts List Main Assembly1562121348791011314151718192016Item Part # Description Quantity1 800-600 Cart assemb

©Titan Tool Inc. All rights reserved. 19Item Part # Description Quantity1 800-078 Electronic cover ...12 800-2

Table of ContentsSafety Precautions ...2Français ...

20 © Titan Tool Inc. All rights reserved.Fluid Section Assembly (P/N 800-300)15101317181920782178911121415166324Install lower packing with the side t

©Titan Tool Inc. All rights reserved. 21Item Part # Description Quantity1 800-325 Upper seal retainer ...12 800-327

22 © Titan Tool Inc. All rights reserved.Low Rider Cart (P/N 800-590)1234567891011121313161514ItemPart # Description Quantity1 590-506 Washer...

©Titan Tool Inc. All rights reserved. 23The following chart indicates the most common sizes and theappropriate materials to be sprayed.Fan widths mea

24 © Titan Tool Inc. All rights reserved.United States Sales & Service1-800-526-5362Fax 1-800-528-4826556 Commerce StreetFranklin Lakes, NJ 07417

9. Attention! Please observe the following when workinginside and outside:No solvent gasses should be carried to the unit. Nosolvent gasses should for

General DescriptionThis airless sprayer is a precision power tool used for sprayingmany types of materials. Read and follow this instructionmanual ca

7. Move the PRIME/SPRAY valve up to the SPRAY position.8. Turn the unit on and set the pressure to minimum byturning the pressure control knob to the

Solid YellowWhen the pressure indicator is solid yellow, the sprayer isoperating between 14 and 124 bar (200 and 1800 PSI). Asolid yellow pressure in

For corners and edges, split thecenter of the spray pattern on thecorner or edge and spray verticallyso that both adjoining sectionsreceive approximat

MaintenanceBefore proceeding, follow the Pressure Relief Procedureoutlined previously in this manual. Additionally, follow allother warnings to reduc

7. Loosen and remove the three motor mounting screws.8. Pull the motor out of the gearbox housing.9. Inspect the armature gear on the end of the motor